Tag Archives: 20-meter band

Amateur radio: California QSO Party, October 7th-8th, 2017

I’m getting close to finishing my first 12 months on the QSO party circuit, and the California QSO Party is one of the biggest of the year.  Being next-door, I figured I would be able to make a lot of low-band QSOs, but wasn’t sure about 20 meters and above.  The contest ran from 16UT on Saturday through 22UT on Sunday (9am Saturday to 3pm Sunday local time).

Unfortunately, I was not able to do anything radio-related until after 6pm on Saturday, then I had to spend 2 hours getting my new 8-foot diameter loop up and fully operational, including a trip to the hardware store.  I finally got on the air at 0330UT (8:30pm CA and AZ time).  The goal of my largest transmitting loop to date was not only to increase my radiated signal on 40 and 80 meters, but also to be able to transmit on 160 meters.  See my recent post for more information on the loop.

As Murphy’s Law would have it, the first station I heard calling CQ on 40 was having trouble hearing everybody, so after 5 minutes I still wasn’t sure if my antenna was working properly.  But, once I gave up on that station, I was able to make a bunch of easy contacts on the band.  Even with losing 15 minutes struggling to get the loop up a little higher (center of the loop at 10.5 feet), I managed 15 QSOs in the first hour on 40.

I switched to 80 meters, where their were even more good signals out of CA and I picked up 24 QSOs in an hour, a new record for me, including 15 in 25 minutes.  This is all “search and pounce” and especially on 80 meters, the bandwidth on a small transmitting loop is very narrow, so I have to adjust the tuning capacitor before just about every QSO.  This is accomplished using a miniVNA Pro as an antenna analyzer, so I switch the antenna input into that, which goes into my laptop.  The vacuum variable capacitor up on the antenna has a 12-volt motor connected to it, and that runs into the shack to my rig power supply and a simple control box.  The miniVNA Pro sends less than 1 milliwatt to the antenna to analyze it, so it doesn’t transmit a bunch of QRM like some “real” antenna tuners that you often hear on the HF bands.

After that, I switched back and forth between 80 and 40 a couple times.  Activity dramatically dropped off at midnight (07UT), not surprisingly.  I got my 56th QSO (including one duplicate) shortly after that, then nothing more.  I listened on 160 for a station that was periodically calling CQ, but he never heard me respond.

I was back at it on Sunday morning a little before 13UT, and made some more contacts on 40 and 80 meters.  Unfortunately, when I finally checked out 20 meters on my smaller loop, I could barely hear any CA stations, just a cacophony of stations from the eastern US calling into CA.  Unfortunately, indeed I was too close to CA to get any QSOs on 20, so I gave up at around 16UT.

I came back for the last 25 minutes of the contest, still not able to work anyone on 20, but picked up several more QSOs on 40.  I ended the contest with 72 QSOs (plus one duplicate), split evenly between 40 and 80.  I worked 37 out of 58 counties, which I felt was pretty good for just two low bands.  Of course, if I was further away, I might not have made as many 80-meter contacts in getting more 20-meter contacts, so it’s hard to say what that would have done to my county total.

Advertisements

Amateur radio: I’m a 2nd Placer!

The 7th Call Area QSO Party (“7QP”) took place on Saturday, May 6th.  The 7th call area contains Arizona, Idaho, Montana, Nevada, Oregon, Utah, Washington, and Wyoming.  Most of these states have sparse populations, so a combined event was begun in 2006 and has become one of the more popular annual QSO parties.  Although the FCC long ago dropped the requirement that your call had to match your call area, most operators do have a call that matches, so the name still fits (in my log it was about 80%).  Also, the Delaware, New England, and Indiana QSO Parties were on the air the same weekend, so there were a lot of cross-contact between the various contests. Continue reading

Amateur radio: ARRL DX contest

This post is rather belated, but I thought I would finally write about the ARRL International DX Phone Contest, the weekend of March 4th.  Basically, as a U.S. mainland station the goal was to contact as many people outside the U.S. mainland in as many countries as possible, and for non-mainland the goal was to contact as many people as possible in the lower 48 states. Continue reading

Video blog episode 009

For this episode, I shot about 2 hours of video of me casually working the 20-meter band on a Saturday with a contest and two state QSO parties in progress, editing the video down to under 30 minutes.  I comment on what I’m hearing, make a few domestic QSOs, one QSO with France, and unsuccessfully work Italy.  All with 80 watts into a homebrew magnetic loop antenna.  Enjoy!

Amateur radio: North American QSO Party, SSB

I’ve been spending a lot of time coming up with a good way of motorizing the tuning shaft of the vacuum variable capacitor, and make the whole assembly modular so I can move it from one loop antenna to another to optimize a particular band.  I only ended up using one antenna during the 12-hour NA QSO Party on Saturday, but it generally went pretty well. Continue reading

Amateur radio: on the air!

I had my 10-foot magnetic loop antenna ready to go for this weekend’s ARRL SSB contest, but realizing that it would only work one band (20 meters) for that contest, at the last minute I decided to build a new loop to finally go on the air as K7HKR. I used this on-line calculator to figure out something optimized for both the 20- and 40-meter bands with the high-voltage variable capacitor I have on hand. This ended up being a 15-foot circumference loop made out of 1/4″ copper coil pipe, which is much easier to bend than the 1/2″ pipe I used for the 10-foot loop. Continue reading